hellcat.parts

As an Amazon Associate and an eBay Partner Network affiliate, we earn from qualifying purchases. Learn more

Top List

Best Exhaust Systems for the Hellcat

How to choose an exhaust for a supercharged Dodge Hellcat — axle-back vs cat-back vs long-tube headers, sound character and highway drone, materials, and which setup fits your Challenger or Charger SRT.

Shopping these parts now? eBay Motors is where the used, OEM, and hard-to-find versions live — prices set by the seller.

On a naturally-aspirated car an exhaust is a power mod; on a supercharged Hellcat it’s mostly a sound mod — and that’s not a knock. The blower already forces the air, so mufflers and tips won’t rewrite the dyno sheet, but they absolutely rewrite the character of a 6.2 supercharged HEMI. The one exception is long-tube headers, which free real flow ahead of the supercharger’s demand on a tuned build. Here’s how to choose an exhaust for a Hellcat, ranked by the decisions that actually matter.

1. Axle-back vs cat-back vs headers — pick your level

This is the first and biggest decision, and it’s about how deep you want to go:

  • Axle-back replaces only the mufflers and tips behind the rear axle. It’s the cheapest, easiest bolt-in that changes the tone — an afternoon in the driveway. Best if you mainly want a louder, deeper note.
  • Cat-back replaces everything from the catalytic converters back: mid-pipe, X- or H-pipe, mufflers, tips. Fuller change in sound plus a small flow benefit, while keeping the OEM cats (and emissions-legal status).
  • Long-tube headers (with a matching mid-pipe) are the real power play. They free flow ahead of the blower and, on a pulley-and-tune car, can be worth a genuine gain — but they demand a tune and often remove or relocate the cats. This is a build-level commitment, not a bolt-on.

Most owners want a cat-back or axle-back for the note; headers belong on a tuned, boost-first build. See where they sit in the order of operations in Best Hellcat Performance Upgrades.

2. Sound character — and the drone question

Exhaust is subjective, but a few design traits predict how a Hellcat will sound:

  • X-pipe blends the banks for a smoother, higher-pitched, more exotic tone; H-pipe keeps a lumpier, old-school muscle rumble.
  • Resonator-delete / straight-through designs are the loudest and meanest — and the most likely to drone at a steady 70-80 mph cruise.
  • Active valve (electronic cut-out) systems cruise quiet and open up under throttle — the best of both worlds if you daily the car.

If you spend real time on the highway, favor a valved or resonated system to kill drone. If it’s a weekend car, a straight-through resonator delete is fine and sounds the part.

3. Materials and build quality

Buy T304 stainless steel for the pipes and, ideally, the tips — it resists rust and heat-bluing far better than the aluminized or T409 stainless used on budget systems. Check the wall thickness and whether the flanges are laser-cut and CNC-mandrel-bent; sloppy bends cost flow and rattle over time. Mandrel-bent T304 with quality band clamps is the durable choice on a car that makes this much heat.

4. Tip size, finish, and fitment

The tips are the only part most people ever see, so match them to the car: 4-inch or 5-inch tips, polished, black chrome, or carbon, and confirm the exit style clears your body’s rear valance. Remember the Challenger and Charger use different rear layouts, so exhausts are body-specific — buy the system listed for your exact car, engine, and year. The same fitment discipline is covered in our Hellcat generations & fitment reference.

Cat-back and axle-back systems leave the factory catalytic converters in place and generally won’t throw a code. Catless or high-flow off-road mid-pipes and header setups can trip the downstream O2 sensors and set a check-engine light unless your tuner squares away the readiness monitors — and they may not be street-legal where you live. If emissions compliance matters, stay cat-back and keep the OEM cats. The FAQ below covers the CEL details.

Where it fits in the build

Exhaust is a character mod first and a power mod only at the header level. The order that makes a Hellcat genuinely faster is boost and tuning first, sound and flow around it:

How to buy

  • New systems, clamps, and tips: Amazon Automotive — browse the exhaust category and check current pricing and availability on Amazon.
  • Used, take-off, or discontinued systems (Borla ATAK cat-backs, Kooks and ARH long-tubes, factory take-off mufflers, hard-to-find valved setups): eBay Motors, via the search buttons below — used listing prices are shown live.

Buy the exhaust for the sound you actually want to live with, mind the drone if you drive it far, and save the long-tube headers for a tuned, boost-first build where they can finally add real numbers.

Find these parts on eBay Motors

For used, OEM, and hard-to-find versions of these parts, eBay Motors is the marketplace — these open live listings for each one. Prices are set by the seller.

Browse every live “dodge hellcat” listing on eBay →

Frequently Asked Questions

How much power does an exhaust add to a Hellcat?
A cat-back or axle-back alone is mostly about sound, not big power — on a supercharged 6.2 the factory exhaust already flows reasonably well, so you're usually looking at single-digit horsepower at the crank from mufflers and tips. The exception is long-tube headers with high-flow or catless mid-pipes: on a pulley-and-tune build those free real airflow ahead of the blower's demand and can be worth a meaningful gain once tuned. Buy a cat-back for the note; buy headers for the numbers, and tune for them.
Will an aftermarket exhaust set off a check-engine light?
A cat-back or axle-back leaves the factory catalytic converters in place and generally will not throw a code. Headers or mid-pipes that remove or relocate the cats (catless or high-flow off-road pipes) can trip the downstream O2 sensors and set a CEL unless your tuner addresses the readiness monitors. If emissions compliance matters where you live, stay cat-back and keep the OEM converters.
Cat-back or axle-back — what's the difference on a Hellcat?
An axle-back replaces only the last section — the mufflers and tips behind the rear axle — so it's the cheaper, easier, bolt-in way to change the tone. A cat-back replaces everything from the catalytic converters back, including the mid-pipe and often an X- or H-pipe, for a fuller change in sound and a small flow benefit. If you mostly want a louder, deeper note, an axle-back does it; if you want the complete acoustic and a little more flow, go cat-back.
Will Hellcat exhaust drone on the highway?
Some do. Drone is the low-frequency resonance you hear at steady 70-80 mph cruise, and straight-through designs without a resonator are the usual culprits. Systems with an X-pipe, a resonator, or active valves tend to cruise quieter and only open up under throttle. If you daily the car on the highway, favor a valved or resonated design; if it's a weekend car, a resonator-delete straight-through is fine and sounds meaner.
Does a Charger and Challenger Hellcat use the same exhaust?
No — the Challenger (two-door) and Charger (four-door) have different wheelbases and rear valance layouts, so cat-backs and axle-backs are body-specific and tip exits differ. Always buy the system listed for your exact body, and confirm the tip diameter and exit style clear your bumper. Long-tube headers are shared by the 6.2 supercharged engine across both, but the mid-pipe that mates to them is still body-specific.

Related Hellcat Reading